Strain Measurement of Fan Blade Roots Under Complex Loading: Multi-Camera DIC Experiments Make Calibration of Simulation Models Grounded in Reality!
Release time:
2026-10-27 18:36
Source:
Aeroengine fan blades represent one of the most extreme service conditions for composite materials: in modern turbofan engines, turbine blades must operate at temperatures exceeding 1600°C, under pressure differentials of several atmospheres, and at rotational speeds of 15,000 rpm, while their root regions simultaneously endure centrifugal tensile forces and torsional loads. Whether a model accurately predicts behavior under such combined loading conditions cannot be determined solely by simulation engineers—it requires validation with experimental data. Over the past year, nearly all of the industry’s most closely watched test–simulation closed-loop cases have relied on the “multi-camera DIC plus model calibration” approach.
01 Simulation calibration under complex loading lacks measured data
Models Lack Ground Truth
The materials and loads on fan blades operate at their performance limits. The joint design between the metallic leading‑edge cap and the composite blade root must simultaneously balance the combined properties of three metals—Ti‑6Al‑4V, Inconel 718, and 15‑5PH—and the IM7/8551‑7 carbon‑fiber composite. Moreover, the blade tip must withstand the combined degradation effects of high‑velocity airflow erosion, oxidation, and thermal fatigue. [1] 。

Figure 1: Cross-sectional model of an engine fan with composite blades at the blade root: The blade root is the convergence point of centrifugal force and torsional loads (reproduced from reference [1]).
Extreme transient conditions are even harder to verify: in blade-out studies, Ti-6Al-4V must withstand high strain rates on the order of 10⁴ s⁻¹ and adiabatic temperature rises exceeding 900°C, with the stress state continuously evolving throughout the failure process—under such conditions, without corresponding experimental data, constitutive and damage models can only rely on assumptions. [2] 。
02 Multi-Camera DIC Layout and Full-Field Measurement
Multi-Camera DIC Setup
The complex load test rig itself represents a superposition of multiple physical fields: the thermo-mechanical-vibrational fatigue testing system for aerospace compressor blades integrates centrifugal loading, temperature control (with an error margin of less than 1%), and high-frequency vibration at 1600 Hz. By further incorporating pre‑damaged specimens to simulate foreign-object damage, the system enables comprehensive investigation of combined fatigue effects. [3] 。

Figure 2: High–low cycle fatigue loading module: the actuator, inner and outer fixtures, vibration exciter, and heating system are integrated into a single unit (reproduced from reference [3]).
The deployment logic for optical measurements has also changed accordingly. In full-scale blade fatigue testing, a dual-camera setup positioned within the root flange observation window, combined with dual light sources for supplemental illumination, enables non-contact, full-field tracking of the blade’s “breathing deformation.” Compared with strain gauges, the average absolute deviations are only 0.84 mm and 0.93 mm—only by leveraging the complementary fields of view of multiple cameras can both the high-stress region at the blade root and the large-deformation region on the blade midsection be simultaneously captured. [4] 。

Figure 3: Dual-camera setup on the blade fatigue test rig: The camera and light source are aligned with the root region of the blade through a flanged observation window (reproduced from reference [4]).
The material-side testing was also conducted in a directional manner: GFRP laminates for blade shear webs were prepared with three fiber orientations—0°, 45°, and 90°—and subjected to uniaxial tensile testing synchronized with acoustic emission monitoring, enabling stepwise localization of matrix cracking, interfacial debonding, and fiber fracture. [5] 。
03 Using measured data to calibrate the FE model
Feed the Model
The value of measured data is realized the moment it is fed into the model. Cross-validation between visual measurement and strain gauges lends credibility to the entire dataset: the mean absolute deviation between two independent tests is within 1 mm, and the deformation trends are highly consistent under typical loads—only with such data entering the FE model does calibration become meaningful. [4] 。

Figure 4: GFRP tensile specimens with three orientations (0°/45°/90°): The orientation distribution must cover the anisotropic parameter space (reproduced from Ref. [5]) (reproduced from Ref. [5]).

Figure 5: Three-dimensional calibration relationship between multi-camera fields of view and the coordinate reference frame: All cameras are unified into a single coordinate system (adapted from reference [4]).
The calibrated model can continue to deliver added value: For a certain hybrid composite blade, a parametric finite element model combined with a machine-learning surrogate model was used for structural optimization, achieving a 15.6% weight reduction while satisfying all constraints and reducing the blade’s total cost by 19%—provided that the model has first been calibrated against experimental data. [6] 。
04 Recommended Implementation Plans
Implementation Roadmap
EikoTwin’s product portfolio precisely covers this link: EikoTwin DIC There is no limit to the number of cameras; after arranging multiple cameras around the specimen, they are calibrated collectively, and the results are output directly in the finite element mesh coordinate system (XYZ)—eliminating the need for conversion when projecting point clouds onto the mesh. DIC results can then be fed directly into solvers such as Ansys for model calibration. EikoTwin Digital Twin uses measured data as boundary conditions and removes idealized constraints, automatically identifying elastic parameters and composite material behavior, and outputs a calibrated digital twin model.
Case study of Safran × Ansys × EikoSim collaboration on turbine blade roots: First, EikoTwin Virtual is used to simulate 360° camera coverage, optimize sensor placement, and estimate measurement uncertainty; during actual testing, four main cameras capture images every 2 seconds while synchronous acoustic emission monitoring detects the initial damage; DIC results are fed directly into Ansys Workbench to complete model calibration—setting an industry benchmark for the closed-loop workflow of “multi-camera DIC + model calibration.”
The message for simulation engineers is clear: under complex loading, model confidence comes not from mesh refinement but from a complete chain of evidence—“virtual pre‑deployment sensor placement → multi‑camera experimental measurement → output in a common coordinate system → FEMU calibration.” Every bit of uncertainty in the root causes deserves to be addressed with measured data.
For every type of load that the blade root is subjected to, there should be a set of measured data to substantiate it.
References
[1] Design of Metal Leading Edge Cap Joint on Thin Wall Composite Fan Blade in Aircraft Engine. Journal of Composites Science, 2026. DOI:10.3390/jcs10030166
[2] Fracture behavior of Ti-6Al-4V in the extreme thermo-mechanical environment of fan blade-out. Scientific Reports, 2026. DOI:10.1038/s41598-026-35044-0
[3] Research on thermal-mechanical-vibration fatigue test technology of aero-engine compressor blade. Frontiers in Materials, 2026. DOI:10.3389/fmats.2026.1783208
[4] Vision-Based Measurement of Breathing Deformation in Wind Turbine Blade Fatigue Test. Journal of Imaging, 2026. DOI:10.3390/jimaging12040174
[5] Mechanical Behavior and Damage Mode Identification of Wind Turbine Blade GFRP Shear Webs Based on Acoustic Emission Detection Technology. Sensors, 2026. DOI:10.3390/s26082363
[6] A machine learning-driven surrogate modeling approach for the structural optimization of hybrid composite wind turbine blades. Structural and Multidisciplinary Optimization, 2026. DOI:10.1007/s00158-026-04320-y
Strain Measurement at the Root of Fan Blades,Multi-camera DIC,FE Simulation Model Optimization,Simulation Model Calibration,Composite Material Strain in Aeroengines



